All Categories
- All Categories
- Izmeritel'nye instrumenty
- Anemometry i balometry
- Detektory provodki
- Gigrometry i vlagomery
- Raskhodnye materialy
- Diski otreznye
- Nasadki dlya graverov
- Nozhi dlya rubankov
- Pil'nye diski
- Ruchnoj instrument
- Kleshchi i bokorezy
- Lomy i gvozdodyory
- Molotki i kuvaldy
- Zaklepochniki
- Ventum products
- Cement-based putties and plasters
- Напольное покрытие на цементной основе
- Изолирующая соль
- Primer
- Система предупреждения протечек
- Контролит
- Elektroinstrument
- Dreli
- Gajkoverty
All-purpose adhesive for tiles KONFOR
Dry mix based on cement, mineral fillers, fractionated sand and modifying additives that improve operational properties.
RANGE OF APPLICATION:
The mixture is intended for laying ceramic, porcelain tiles of small and medium sizes, slabs of natural and artificial stone with water absorption of at least 1% on vertical and horizontal plastered, concrete, gas concrete, brick and other mineral primary structures. Glue is a mortar of wide application: it can be used to fill tile joints, level the surface with a layer of up to 5 mm. For interior and exterior use.
PREPARATION OF PRIMARY STRUCTURE:
The primary structure must be strong, thoroughly cleaned from dust, dirt, oils, etc. Roughnesses deeper than 5 mm must first be leveled with plaster mixes. Before carrying out work, highly absorbent structures should first be treated with a deep penetration primer. The base must be strong, thoroughly cleaned from dust, dirt, oils, etc. Roughnesses deeper than 5 mm must first be leveled with plaster mixes. Before carrying out work, highly absorbent structures should first be treated with a deep penetration primer.
PREPARATION OF MORTAR:
1. Take a precisely measured amount of water (5.75 - 6.75 liters per 25 kg bag.)
2. Pour the mixture into water;
3. Stir with a construction mixer or drill with a special nozzle until a homogeneous mass is obtained;
4. Make a technological pause of 5-10 minutes for maturing the solution;
5. Stir repeatedly.
After that, the glue is ready for use within 4 hours with periodic stirring.
OPERATIONAL PROCEDURE:
The adhesive solution is applied to the prepared primary structure using a notched trowel. The solution should be applied to a surface area that can be tiled for 15 minutes. After application of adhesive tile is applied to the primary structure and pressed. Within 20 minutes after laying the position of a tile can be adjusted. Tile joints must be cleaned immediately after laying the tiles. Work on filling tile joints is done after the adhesive joint has completely dried (drying out time is 16 to 24 hours). Walking on the floor claddings can be carried out no earlier than in 24 hours after laying the tiles. Tile cladding can be fully operational after 3 days. The tool is cleaned with water immediately after use.
OCCUPATIONAL SAFETY:
The dry mix contains cement. When mixed with water, the product gives an alkaline reaction. To prevent skin irritation, avoid contact with exposed areas of the body. In case of contact with eyes, rinse immediately with water and consult a doctor if necessary. In addition to the above information, you should be guided by the safety instructions in construction.
| Тех характеристики | |
| Adhesion not less than, MPa | 1,0 |
| Color | gray |
| Drying time, h | 24 |
| Frost resistance, cycles | 50 |
| Maximum grain size, mm | 1,25 |
| Open time, min | 15 |
| Operating temperature | from -50 °C to +70 °C |
| Recommended layer thickness, mm | от 3 мм до 6 мм |
| Solution lifetime, h | 4 |
| The consumption of the mixture when working with a spatula | 2,8 кг/м² when applied to a flat surface |
| The temperature of the work | from +5°C to +30 °C |
| Tile adjustment time, min | 10 |